There's a lot more to printing from the Linux command line than the lp command. Check out some of the many available options.
Getting your Linux system to send print jobs to your local printer might seem like a challenge, especially when you want to print double-sided or in landscape mode, but it’s really a lot easier than you might imagine.
Know your printer
If you’re just starting to use the printer, you might first want to make sure that the lp command is in your search path with a command like this:
$ which lp /usr/bin/lp
You can then check the status of your printer with an lpstat command like this one:
$ lpstat -p -d printer HP-Color-LaserJet-CP2025dn is idle. enabled since Sat 08 Jun 2024 10:20:01 AM EDT system default destination: HP-Color-LaserJet-CP2025dn
Note that the -p option provides the printer description while the -d specifies the default printer. In this example, there is only one printer. You can use these options separately as shown below.
$ lpstat -p
printer HP-Color-LaserJet-CP2025dn is idle. enabled since Sat 08 Jun 2024 12:03:54 PM EDT
Waiting for printer to finish.
$ lpstat -d
system default destination: HP-Color-LaserJet-CP2025dn
If you’re curious about printer options, you can use the lpoptions command like this:
$ lpoptions copies=1 device-uri=socket://192.168.0.15 finishings=3 job-cancel-after=10800 job-hold-until=no-hold job-priority=50 job-sheets=none,none marker-change-time=1717856401 marker-colors=#000000,#00FFFF,#FF00FF,#FFFF00 marker-levels=5,28,68,27 marker-names='Black\ Cartridge\ HP\ CC530A,Cyan\ Cartridge\ HP\ CC531A,Magenta\ Cartridge\ HP\ CC533A,Yellow\ Cartridge\ HP\ CC532A' marker-types=toner,toner,toner,toner number-up=1 print-color-mode=color printer-commands=AutoConfigure,Clean,PrintSelfTestPage printer-info='HP Color LaserJet CP2025dn' printer-is-accepting-jobs=true printer-is-shared=true printer-is-temporary=false printer-location='HP Color LaserJet CP2025dn' printer-make-and-model='HP Color LaserJet CP2020 Series with Duplexer Postscript (recommended)' printer-state=3 printer-state-change-time=1717856401 printer-state-reasons=toner-low-report printer-type=8425564 printer-uri-supported=ipp://localhost/printers/HP-Color-LaserJet-CP2025dn
To view each option on a line by itself, you can send the output of the lpoptions command to a command like that below which turns the blanks in the output into newlines (‘\n’), thus separating the options. Notice all the details provided as you move through them looking at a section at a time with the more command. Even the colors of the toner cartridges are included in this example.
$ lpoptions | tr " " '\n' | more copies=1 device-uri=socket://192.168.0.15 finishings=3 job-cancel-after=10800 job-hold-until=no-hold job-priority=50 job-sheets=none,none marker-change-time=1717856401 marker-colors=#000000,#00FFFF,#FF00FF,#FFFF00 marker-levels=5,28,68,27 marker-names='Black\ Cartridge\ HP\ CC530A,Cyan\ Cartridge\ HP\ CC531A,Magenta\ Cartridge\ HP\ CC533A,Yellow\ Cartridge\ HP\ CC532A' marker-types=toner,toner,toner,toner number-up=1 print-color-mode=color printer-commands=AutoConfigure,Clean,PrintSelfTestPage printer-info='HP
If you have multiple printers available, you can use the -p option to specify a particular printer.
$ lpoptions -p LaserJet
With the -v option, the lpinfo command will list drivers and related information, including the printer’s IP address.
$ lpinfo -v file cups-brf:/ network beh direct hp network ipps network lpd network socket network http network ipp network https network smb direct hpfax network socket://192.168.0.15 network dnssd://HP%20Color%20LaserJet%20CP2025dn%20(F47468)._pdl-datastream._tcp.local/
Now that we’ve taken a look at all the details you can view about your printers, let’s dive into printing.
Using the lp command
To print a document on the default printer, just use the lp command followed by the name of the file that you want to print. If the filename includes blanks (rare on Linux systems), either put the name in quotes or start entering the file name and press the tab key to invoke file completion (as shown in the second example below).
$ lp mystory $ lp the\ whole\ story request id is HP-Color-LaserJet-CP2025dn-2 (1 file(s))
Use the lpq command to view the files in the printer queue. Note, however, that some files will print so quickly that they’ll be done before you hit the enter key after typing “lpq” and you won’t get a listing. In this case, I put the lpq command on the same line to avoid the print finishing too quickly.
$ lp the\ whole\ story ; lpq request id is HP-Color-LaserJet-CP2025dn-3 (1 file(s)) HP-Color-LaserJet-CP2025dn is ready and printing Rank Owner Job File(s) Total Size active shs 3 the whole story 1024 bytes
Printing multiple copies of a file
With the -n option, the lp command allows you to specify the number of copies of a printout you want.
$ lp -n 11 agenda
Cancelling a print job
To cancel a print job, you can use the cancel or lprm command. If you don’t act quickly (depending on how many print requests are in the queue), the print job might finish before your cancel command is run:
$ cancel 229 cancel: cancel-job failed: Job #229 is already completed - can't cancel.
Printing in double-sided mode
To print in two-sided mode, you can issue your lp command with a sides option that will allow you to print on both sides of the paper and control which edge the paper will turn on. This setting represents the normal way that you would expect two-sided portrait documents to look.
$ lp -o sides=two-sided-long-edge Notes.pdf
If you want all of your documents to print in two-side mode turning on the short edge, you could change your lp settings by using the lpoptions command to change the setting for sides.
$ lpoptions -o sides=two-sided-short-edge
It’s easy to return the setting to one-sided, though generally wiser to simply specify the option as needed rather than changing the default.
$ lpoptions -o sides=one-sided
Make note of the difference between using an option and changing a default setting. The -o in the first command in this section makes use of an option. The second two commands change settings.
Printing in landscape mode
To print in landscape mode, you would specify the landscape option with the lp command like this followed by the file name.
$ lp -o landscape penguin.jpg
Wrap-up
You have a lot of options when it comes to printing from the Linux command line. Hopefully this post has provided some insights into how to view options and use the lp command’s many options.
